Stripper Creator Editor

General

This page is displayed in the editor whenever there is a currently selected stripper area/region, and the Select  tool or other editing tool is running.

Stripper Creator Editor – General

Machine Settings

This option allows you to change the Stripper Machine settings that have been applied to the currently selected stripper area/region. From the pulldown, select the settings and then press the Apply change button.

System Settings

This option allows you to view the Stripper System settings that were used to create the currently selected stripper area/region

Bridges

This allows you to view the number of bridges that have been added to the currently selected stripper area/region, and any warnings related to this number.

Replicas

This allows you to view the number of replicas of the currently selected stripper area/regions exist. Press the Break link button to remove the links so that editing one will no longer affect all of the replicas.  

Remove

This option allows you to remove the currently selected stripper area/region.

Rule

This page is displayed in the editor whenever there is a currently selected stripper area/region with a currently selected rule, and the Select  tool or other editing tool is running.

The name of the page reflects that of the current rule type, and may be Restriction, Male Symbol, Female Symbol, Normal, Point Slot, Parallel Offset, Knife to Knife, Castle Top, Riding Knife Radius, Radius, Wood Bridge, Trim Waste, First Knife, Solitaire, Bridge, Nick, SK Nose, BEBL, StripClip SPC1, StripClip SC10V, StripClip SC11V, StripClip SCLV, StripClip SC10H, StripClip SC11H, StripClip SCLH, StripClip MiniClip, StripClip MaxiClip, StripClip SR10, StripClip RRS, StripClip RRL, Simple, Free, Combi, Riding Knife Simple or Unknown. If the current restriction is a female component, then the name will be the name of that component.

Stripper Creator Editor - Restriction Rule

Chamfer

Width

This allows you to edit the width, if applicable, and view any warnings related to this value.

Depth

This allows you to edit the depth, if applicable, and view any warnings related to this value.

Angle

This allows you to edit the insertion angle, if applicable, and view any warnings related to this value.

Flipped female symbol

If the rule is a Trim Waste restriction, then this option allows you to flip the female symbol so that it is placed the other way around.

Inferences

This allows you to view the number of inferences of the currently selected rule within the stripper area/regions. Press the Break link button to remove the links so that editing one will no longer affect all of the inferences.  

Remove Rule

This option allows you to remove the currently selected rule.

Nick

Use this checkbox to add or remove a nick from the component.

Rotate nick

Switch this checkbox on to rotate the nick symbol through 180 deg.

Symbol

You can change the nick symbol by selecting the required one from the drop down list.

Components

This page is displayed in the editor whenever there is a currently selected stripper area/region with a currently selected rule which has  male components associated with it, and the Select  tool or other editing tool is running.

Stripper Creator Editor - Components

Component Offset

This option allows you to edit the male component offset.

Current Stripping Pin/Male Knife/Claw/Fork

These options relate to a single selected component within the set of components at a time.

Depending on whether the component is a Male Component, or just a symbol or an entity, a pulldown or entry field is available to allow you to change the component, and the length, size or diameter of the component is displayed.

If Alternative Symbols are available for the component, from the pulldown, select the name of the alternative symbol you wish to use.

If the component is of Claw type, then check the Flipped option if you wish to place the left hand component, or leave it unchecked if you wish to place the right hand component.

Press the Reorient button to cycle through the four possibilities for the orientation of the Claw component.

Rotate

This option allows you to edit the rotation of the current component.

Offset

This allows you to offset the anchor position for the component, either to the left or the right.

Previous & Next

These buttons allow you to move through the group of components one by one to make one current.

Reset

This option allows you to reset the current component back to its original state before it was edited.

Remove

This option allows you to remove the current component.

Auto Side Rotate

This allows you to override the Side Rotate  option, which determines whether components are automatically rotated to the side, for these dynamic stripping components.

Remove DSC

This option allows you to remove all the dynamic stripping components.

Move

This page is displayed in the editor whenever there is a currently selected stripper area/region with a currently selected rule which is movable, and the Select  tool or other editing tool is running.

Stripper Creator Editor - Move

Centre

This allows you to manually nudge the centre of the rule, either to the left or right.

Clip

This allows you to rotate the female StripClip component relative to its insertion point.

Male

This page is displayed in the editor whenever there is a currently selected stripper area/region which may have male waste settings applied to it, and the Select  tool or other editing tool is running.

Stripper Creator Editor - Male

Waste Settings

This option allows you to change the Male Waste settings that have been applied to the currently selected stripper area/region. From the pulldown, select the settings and then press the Apply change button. Press the Remove button to remove any applied male waste settings.

Offsets

Offset

This allows you to override the standard offset value defined for the male waste.

Minimum

This allows you to override the minimum offset value defined for the male waste.

Coverage/Effective Offsets

This allows you to override the effective offset values defined for the male waste coverage for each component type.

Male Knives/Claws

Slot offset

This allows you to override the slot offset value defined for the male waste.

Wooden Block

Offset

This allows you to override the wooden block offset value defined for the male waste.

Minimum Thickness

This allows you to override the wooden block minimum thickness value defined for the male waste.

Wooden Block

This page is displayed in the editor whenever there is a currently selected stripper area/region which has male waste settings applied to it which define a wooden block, and the Edit Support Pin  tool is running.

Stripper Creator Editor - Wooden Block

Support Pin

Offset

This allows you to edit the offset of the support pin from the edge of the wooden block.

Major Symbol

If this option is checked, then the major symbol is used for the support pin; otherwise, the minor symbol is used.

Did you find it helpful? Yes No

Send feedback
Sorry we couldn't be helpful. Help us improve this article with your feedback.

You may like to read -